ngHobbies
HITECH HS-85BB BALL BEARING MICRO SERVO
Detailed Specifations:, Motor Type:, 3 Pole, Bearing Type:, Top Ball Bearing, Speed:, 0.16 / 0.14 sec @ 60 deg, Torque:, 41.66 / 48.6 oz.in (4.8v/6v), Size:, 1.14" x 0.51" x 1.18", Weight:, 0.67oz, Documentation:, Servo Manual:, Click here, Data sheet:, Click here, Hitec Servo Chart:, Click here,
The HS-85BB feature a high power motor for greater speed ...ngHobbies
3DR PIXHAWK AUTOPILOT W/O GPS AND PPM ENCODER
| • Weight | 38g (1.31oz) |
| • Width | 50mm (1.96") |
| • Thickness | 15.5mm (.613") |
| • Length | 81.5mm (3.21") |
Note: Pixhawk is a PPM-input autopilot, which means that it gets RC input from a single cable to the receiver, either via the PPM port, the Futaba S.BUS port, or the special satellite receiver port for Spektrum gear. Most modern RC receivers (and all those sold by 3D Robotics) allow for PPM output, but some, such as non-S.BUS Futaba receivers, do not., Pixhawk includes:, • Pixhawk autopilot, Microprocessor:, • 32-bit STM32F427 Cortex M4 core with FPU, Sensors:, • ST Micro L3GD20 3-axis 16-bit gyroscope, Interfaces:, • 5x UART (serial ports), one high-power capable, 2x with HW flow control, Power System:, • Ideal diode controller with automatic failover, Weight and Dimensions:,
Pixhawk is an advanced autopilot system designed by the PX4 ...ngHobbies
AEROSIM RC TRAINING SIMULATOR
Features:, - Very realistic flight characteristics. The flight performance and physics of the models is very realistic - this usually is found only at a much higher priced simulators., See it in action here:, AeroSIM RC - Simulador Aeromodelismo Radio Control Flight Simulator, Download the trial version:, Click here,
The AeroSIM RC is the first simulator which was developed ...ngHobbies
HITECH HS-55 FEATHER SERVO
Detailed Specifations:, Motor Type:, Coreless, Bearing Type:, None, Speed:, 0.17 / 0.14 sec @ 60 deg., Torque:, 15 / 18 oz.in (4.8v/6v), Size:, 0.89" x 0.45" x 0.94", Weight:, 0.28oz, Documentation:, Servo Manual:, Click here, Data sheet:, Click here, Hitec Servo Chart:, Click here,
The HS-55 set the standard for affordable performance, offering precision ...ngHobbies
HITECH HS-82MG STANDARD MICRO SERVO
Detailed Specifations:, Motor Type:, 3 Pole, Bearing Type:, None, Speed:, 0.12 / 0.10 sec @ 60 deg., Torque:, 38.88 / 47.22 oz.in (4.8v/6v), Size:, 12.00" x 1.17" x 1.16", Weight:, 0.66oz, Documentation:, Servo Manual:, Click here, Data sheet:, Click here, Hitec Servo Chart:, Click here,
We take one our top selling servos and make it ...ngHobbies
ARDUPILOT MEGA 2.5+ FULLY ASSEMBLED SYSTEM
Features:, Arduino Compatible!, :, ArduPlane code, :, MPU-6000, Six-Axis (Gyro + Accelerometer) MEMS MotionTracking™,
The ArduPilot Mega 2.5 is a complete open source autopilot ...ngHobbies
MIKROKOPTER BASIKSET OKTO XL
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-OktoXL |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
MIKROKOPTER BASIKSET HEXA XL
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-HexaXL |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
MIKROKOPTER QUADRO XL
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-Quadro |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
MIKROKOPTER BASIKSET L4-ME
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included in this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-Quadro?action=show&redirect=en%2Fassembly |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, 1 x preassembled FlightCtrl ME V2.1 with Altitude Sensor, Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
MIKROKOPTER BASIKSET HEXA 2
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-Hexa |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
MIKROKOPTER BASIKSET OKTO 2-26
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-Okto |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
MIKROKOPTER BASIKSET OKTO
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-Okto |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
ARDUPILOT MEGA 2.6+ FULLY ASSEMBLED SYSTEM
Features:, Arduino Compatible!, :, ArduPlane code, :, MPU-6000, Six-Axis (Gyro + Accelerometer) MEMS MotionTracking™,
The ArduPilot Mega 2.6 is a complete open source autopilot ...ngHobbies
QUADRO2 XL COMBI ASSEMBLED DISTRIBUTION BOARD
| • voltage | 10 to 30V -> 3 -7S Lipo |
| • current | up to 60A (per BL-Unit) and 120A (all together) with appropriate cooling |
| • Silent Start | test tone at startup can be disabled |
| • hole | 3mm |
| • weight | ca. 109g |
IMPORTANT:, Use FlightCtrl Firmware V2.02 (or greater), otherwise read the instructions in the wiki !, : The BL-Ctrl 3.0 controller is specifically designed and optimized for our motors. For maximum stability of the MikroKopter set-points are set almost instantaneously on the motor. If other motors (especially larger power classes) are used with this controller, this fast change of set-points can easily lead to very high peak currents, which bring the BL-Ctrl control to the limit or an overload. This is no fault of BL-Ctrl3.0 controller, but a systemic property., Power:, Mechanical data:, , • Dimensions (W x H ):, In the package:, • 2 SMD preassembled, programmed and tested boards already mounted and soldered, Links:,
4 ESCs on two boards! Extremely fast brushless controllers version ...